Kanske till någon hjälp, då du verkar ha ett bränsle/luft problem. It also indicates that the fuel trims reached their limit of adding fuel while trying to compensate for a actual or perceived rich condition. When the fuel trims reach their rich correction limit, the PCM (Powertrain Control Module) sets a P0170, indicating a problem or malfunction in the fuel trims. It may also have a P0173 referring to the same malfunction but on bank two. Symptoms Symptoms of a P0170 DTC may include: MIL (Malfunction Indicator Lamp) Illumination Start and stall Poor fuel economy Black smoke at tailpipe Hesitation/misfire at idle or under load Causes Potential causes include a vacuum leak, unmetered air leaks Fuel saturated engine oil Leak in turbo air charge hoses (if equipped) Possibly bad O2 sensor (If Mercedes, may require adaptation with M-Benz compatible scan tool.) Oil contamination in MAF connector or O2 sensor connectors. Also check ignition coils, cam and crank sensors, and oil sensor for leakage contributing to oil intrusion in wiring harness. Defective MAF (Mass Air Flow) sensor (especially on Mercedez-Benz and other European autos. There are a lot of problems with aftermarket MAF sensors.) Defective fuel pressure regulator Leaking camshaft adjuster solenoids (Mercedes-Benz). NOTE: for some Mercedes-Benz models there is a service recall for a crankcase vent hose located under the intake manifold. It should be checked for leaks/cracking and also operation of check valve in the hose. The check valve should flow only one way. Possible Solutions It should be stated right off the bat that the most common problem associated with this code is the MAF sensor or air mass meter. This is especially the case with Mercedes-Benz and Volkswagen and other European cars. At time of writing, you don't normally see this code with American-made cars, and minimally with Asian, and, to be honest, I have no idea why. It appears to me that the PCM (powertrain control module) logic used by some European car manufacturers to set a P0170 (or P0173) fault code simply isn't used by American vehicle manufacturers. It is more common to see P0171, 0174, 0172, 0175 codes set with regard to fuel trim malfunctions on American cars. There is very little information on the setting conditions for a P0170, or P0173, but what information that is available almost seems to be a redundancy of the P0171,4,2 & 5 setting conditions. I'm sure there's a reason for it, but I can't get anyone to tell me what that is. The similarities between them may be why we don't see this code surface on domestic vehicles very often. It's simply unnecessary. So, simply put, if you have a P0170, your PCM noticed that the fuel trims reached their rich correction limit. Basically it's adding fuel to try to compensate for a lean condition, real or perceived. If you have this code and access to a scan tool, observe the MAF sensor reading in grams/sec. The reading will be different for different automobiles, so get a good spec. I'm going to stick with what would be normal for a Mercedes (1.8L), since they have the bulk of the trouble. Expect to see at idle 3.5-5 g/s (ideally). At 2500 RPMs with no load it should be between 9 and 12 g/s. On road test, at WOT (wide open throttle) it should be 90 g/s or well above. If it's not in specs, replace it. Be careful of Ebay MAFs. Often they don't work according to OE specifications. If the MAF checks out and there is no oil intrusion at the connector, check fuel pressure and ensure that there are no leaks at the regulator internally or externally. Check all vacuum hoses and confirm none are cracked, disconnected or missing. Make sure there are no vacuum leaks at the intake manifold gaskets or tears in the air supply hose. If the engine is turbo charged, be sure the hoses are in good condition and have no leaks. Leaking turbo pressure hoses could cause a rich condition. Inspect the condition of crankcase vent hose under intake manifold and operation of check valve in the hose. (In the "What are the causes?" section) If there doesn't appear to be any problems with the fuel pressure, MAF or vacuum hoses, then inspect the O2 sensor connectors for oil intrusion. A bad O2 sensor could cause a P0170, or P0173. Repair cause of oil leak and replace oil-fouled O2 senso
Read more at: https://www.obd-codes.com/p0170
Copyright OBD-Codes.com
Ja får upp den koden igen p0170,får kolla lamda
Nersmutsade sensorer kan ge alla möjliga konstiga fel. Kolla de först och rengör. Brukar köra med bromsrengöring. Har funkat bra hitintills. Lättare att börja med rengöring, innan byte av komponenter. Smutsig MAF sensor kan krångla till det ordentligt.
Vart sitter denne MAF sensor
Ser bara gasspjäll på denne
Jag hittade den,får kolla når jag kommer hem med å rensa den
Rensade mapp i går och den gick bättre en liten stund men började på igen och fick frsm samme felkod igen,så den måste dra någon luft om inte det är lambda som är kass,få prova mete strömmen på den
Nej nu bliver det snart skroten,får ingen fullgas och forsatt svårstartad,har bytt lmm också
Har du inte möjlighet att kolla den med en tester så man kan se realtidsvärden?
Det kan vara en tempsensor eller vevaxel/kamaxelgivare eller något annat enkelt som spökar och det ser man oftast ganska enkelt med en tester.
Vet onte men i går når den va varm gick den som en klocka,men på morgonen va den svårstartad igen
[attachment file=62909]
Vad är dette
Når man kollar resistansen så ska väl den va så låg som möjlig
Det är tomgångsventilen, vet ej vad motståndet ska vara, men kolla att där inte är sot i den, hänger den sig kan man få en del knasiga problem med luft bränsle blandningen.
Kolla denna länken, men det borde bli felkod om kablaget låg emot
https://www.landyzone.co.uk/land-rover/freelander-engine-idle-speed-erratic-bulletin-0007.152876/
Vet du vart man kan köpa en såden väntil,hittar inget på netet
Land Rover bör ha, men finns alldeles säkert på skroten eller kanske någon i gruppen som har begagnad
